articles/Lighting/onelightportraits-page5

One Light Portraits - part 5 of 1 2 3 4 5

by Dave Montizambert Published 01/11/2005

When I made this image I included another panel with white nylon stretched over it to reflect stray light from the main-light panel back into the shadow side of Sylvianne. To control how bright the shadows appear you simply move the panel closer or further away from the shadow side of the subject and/or switch to silver lame if you want an even higher return. In the end I discarded the fill panel because more than enough light was already filling in the shadows from stray light bouncing off the wall on the camera right side of the set. If I had wanted the shadows darker, I would have simply blocked this wall fill-light by placing a panel with black fabric stretched over it.

And now for even more cod-liver oil. A shadow is an area on a subject or object that receives no light whatsoever from the main source of illumination. However, it may receive some light from an extraneous ambient source (eg fill light, fill card, open sky). The shadow is always darker than the subject's or object's true tonality. In other words it is an under-exposed area and is under-exposed because it receives no illumination whatsoever from the main-light source.

The reason that the light on Sylvianne in Frame Three is more forgiving to imperfections of the flesh compared with the light quality in Frame 1 is due to control over an area of lighting called Shadow Edge Transfer. When light from the main-light begins to see over into the shadow, this contaminated area is no longer considered shadow. This transition area between lit and unlit will be brighter than the shadow, yet darker than the fully lit area. And since, by definition, a shadow is an area of the subject that receives no illumination whatsoever from the main-light, then these borderline areas are considered to be transfer areas. All of our senses are very sensitive to rates of transfer. How much you notice a change will be dependent upon the actual rate of transfer. For instance, if you walked into a kitchen and the refrigerator was making a loud humming noise, it would draw your attention. However, your sense of hearing would acclimatize, as all our senses do, to the sound after a few minutes. If it increased in volume over the span of one second, a rapid transfer, it would immediately draw your attention. If it were to increase in volume over a period of half an hour, you probably wouldn't notice the change at all. The same is true with vision when you are lighting. If you can take the edge of the shadow and make it transfer over a larger area, it becomes less noticeable. This is a particularly good thing to consider when lighting people. In portraiture, unlike fashion, photographer's subjects are usually regular people. Regular people tend to have less than perfect flesh - they have bumps and wrinkles on their faces. Caucasian flesh tone is light. We see shape and form on Caucasians pre-dominantly with shadow. Wherever there is a bump or wrinkle, a shadow is formed. If you are able to make some of the main-light see around into the shadow, a softer rate of transfer will occur creating a softer edge. Soft edge transfer is part of Soft Light Quality.

A soft-edged shadow draws less attention. Creating a gradual transfer from a shadow into the main-lit area of the face helps reduce retouching in portraiture. For example, in Frame One of Sylvianne, look at the rough textured flesh on her neck on the edge of the shadow. Compare this with the same area on Frame Three of Sylvianne, the texture is less noticeable, the larger lighFinal imaget source in Frame Three has eaten further into the shadow creating a much softer Shadow Edge Transfer than could the small light source in Frame 1.

The effect of size of source on transfer area is directly related to the dimensions of the light source. If a main-light were enlarged by four times, the main-light would see four times further into the shadow - the Shadow Edge Transfer area would then cover a four times greater area. A light source is visually two-dimensional; it is made up of height and width. You can create two different rates of transfer with one light source by choosing a light source made up of two different dimensions. A "strip-light" does exactly this; it is a small light source in one direction and a larger light source in the other. This creates softer edge transfers one-way and harder edges the opposite way. On a face, placing a 3ft by 6in strip-light vertically will create soft shadow edges up and down and hard shadow edges left to right - horizontal facial lines or wrinkles would be less noticeable than vertical ones.

This lighting set-up used on Sylvianne solves a lot of problems. It allows us to create pleasing lighting on a subject against a pure white background with minimal equipment, it reduces retouching, and it allows us to change backgrounds really fast. I still use this set-up today, originally when I was a starving disciple of Dean Collins, I would use white bed-sheets for panels, iron plumbing pipe set in an empty paint can full of concrete for stands, an inexpensive 500 watt tungsten security or work light, and 400ISO film with a long exposure (f5.6 at a 1/15th). However I must say it is a lot easier with Chimera light panels and a Whitelightning X1600 strobe head and my clients don't think they have shown up on laundry day.

Please Note:
There is more than one page for this Article.
You are currently on page 5

Contact Dave Montizambert

1st Published 01/11/2005
last update 09/12/2022 14:57:08

More Lighting Articles

There are 23 days to get ready for The Society of Photographers Convention and Trade Show at The Novotel London West, Hammersmith ...
which starts on Wednesday 15th January 2025

Photography Articles from the Professional Imagemaker

One Light Portraits - part 5 of 1 2 3 4 5